#!/usr/bin/env python3

"""
rpi-eeprom-config
"""

import argparse
import atexit
import os
import subprocess
import string
import struct
import sys
import tempfile
import time

VALID_IMAGE_SIZES = [512 * 1024, 2 * 1024 * 1024]

BOOTCONF_TXT = 'bootconf.txt'
BOOTCONF_SIG = 'bootconf.sig'
PUBKEY_BIN = 'pubkey.bin'
CACERT_DER = 'cacert.der'
BOOTCODE_BIN = 'bootcode.bin'
BOOTSYS_BIN = 'bootsys'
UPDATE_TIME_FILENAME = 'updatetime'

# Each section starts with a magic number followed by a 32 bit offset to the
# next section (big-endian).
# The number, order and size of the sections depends on the bootloader version
# but the following mask can be used to test for section headers and skip
# unknown data.
#
# The last 4KB of the EEPROM image is reserved for internal use by the
# bootloader and may be overwritten during the update process.
MAGIC = 0x55aaf00f
PAD_MAGIC = 0x55aafeef
MAGIC_MASK = 0xfffff00f
FILE_MAGIC = 0x55aaf11f # id for modifiable files
FILE_HDR_LEN = 20
FILENAME_LEN = 12
TEMP_DIR = None

# Modifiable files are stored in a single 4K erasable sector.
# The max content 4076 bytes because of the file header.
ERASE_ALIGN_SIZE = 4096
MAX_FILE_SIZE = ERASE_ALIGN_SIZE - FILE_HDR_LEN

# An AB EEPROM image contains a populated read only section, a populated first partition,
# an empty second partition and then two empty journal sections.
READ_ONLY_SIZE = 64 * 1024
PARTITION_SIZE = 988 * 1024

DEBUG = False
def debug(s):
    if DEBUG:
        sys.stderr.write(s + '\n')

def rpi4():
    compatible_path = "/sys/firmware/devicetree/base/compatible"
    if os.path.exists(compatible_path):
        with open(compatible_path, "rb") as f:
            compatible = f.read().decode('utf-8')
            if "bcm2711" in compatible:
                return True
    return False

def rpi5():
    compatible_path = "/sys/firmware/devicetree/base/compatible"
    if os.path.exists(compatible_path):
        with open(compatible_path, "rb") as f:
            compatible = f.read().decode('utf-8')
            if "bcm2712" in compatible:
                return True
    return False

def exit_handler():
    """
    Delete any temporary files.
    """
    if TEMP_DIR is not None and os.path.exists(TEMP_DIR):
        tmp_image = os.path.join(TEMP_DIR, 'pieeprom.upd')
        if os.path.exists(tmp_image):
            os.remove(tmp_image)
        tmp_conf = os.path.join(TEMP_DIR, 'boot.conf')
        if os.path.exists(tmp_conf):
            os.remove(tmp_conf)
        os.rmdir(TEMP_DIR)

def create_tempdir():
    global TEMP_DIR
    if TEMP_DIR is None:
        TEMP_DIR = tempfile.mkdtemp()

def pemtobin(infile):
    """
    Converts an RSA public key into the format expected by the bootloader.
    """
    # Import the package here to make this a weak dependency.
    from Cryptodome.PublicKey import RSA

    arr = bytearray()
    f = open(infile,'r')
    key = RSA.importKey(f.read())

    if key.size_in_bits() != 2048:
        raise Exception("RSA key size must be 2048")

    # Export N and E in little endian format
    arr.extend(key.n.to_bytes(256, byteorder='little'))
    arr.extend(key.e.to_bytes(8, byteorder='little'))
    return arr

def exit_error(msg):
    """
    Trapped a fatal error, output message to stderr and exit with non-zero
    return code.
    """
    sys.stderr.write("ERROR: %s\n" % msg)
    sys.exit(1)

def shell_cmd(args, timeout=10, echo=False):
    """
    Executes a shell command waits for completion returning STDOUT. If an
    error occurs then exit and output the subprocess stdout, stderr messages
    for debug.
    """
    start = time.monotonic()
    arg_str = ' '.join(args)
    bufsize = 0 if echo else -1
    result = subprocess.Popen(args, bufsize=bufsize, stdout=subprocess.PIPE, stderr=subprocess.PIPE)

    while time.monotonic() - start < timeout:
        if echo:
            s = result.stdout.read(80).decode('utf-8')
            if s != "":
                sys.stdout.write(s)
        if result.poll() is not None:
            break

    if result.poll() is None:
        exit_error("%s timeout" % arg_str)

    if result.returncode != 0:
        exit_error("%s failed: %d\n %s\n %s\n" %
                   (arg_str, result.returncode, result.stdout.read().decode('utf-8'), result.stderr.read().decode('utf-8')))
    elif not echo:
        return result.stdout.read().decode('utf-8')

def get_latest_eeprom():
    """
    Returns the path of the latest EEPROM image file if it exists.
    """
    latest = shell_cmd(['rpi-eeprom-update', '-l']).rstrip()
    if not os.path.exists(latest):
        exit_error("EEPROM image '%s' not found" % latest)
    return latest

def apply_update(config, eeprom=None, config_src=None):
    """
    Applies the config file to the latest available EEPROM image and spawns
    rpi-eeprom-update to schedule the update at the next reboot.
    """
    if eeprom is not None:
        eeprom_image = eeprom
    else:
        eeprom_image = get_latest_eeprom()
    create_tempdir()

    # Replace the contents of bootconf.txt with the contents of the config file
    tmp_update = os.path.join(TEMP_DIR, 'pieeprom.upd')
    image = BootloaderImage(eeprom_image, tmp_update)
    image.update_file(config, BOOTCONF_TXT)
    image.write()

    config_str = open(config).read()
    if config_src is None:
        config_src = ''
    sys.stdout.write("Updating bootloader EEPROM\n image: %s\nconfig_src: %s\nconfig: %s\n%s\n%s\n%s\n" %
                     (eeprom_image, config_src, config, '#' * 80, config_str, '#' * 80))

    # Ignore APT package checksums so that this doesn't fail when used
    # with EEPROMs with configs delivered outside of APT.
    # The checksums are really just a safety check for automatic updates.
    args = ['rpi-eeprom-update', '-d', '-i', '-f', tmp_update]

    # If flashrom is used then the command will not return until the EEPROM
    # has been updated so use a larger timeout.
    shell_cmd(args, timeout=180, echo=True)

def edit_config(eeprom=None):
    """
    Implements something like 'git commit' for editing EEPROM configs.
    """
    # Default to nano if $EDITOR is not defined.
    editor = 'nano'
    if 'EDITOR' in os.environ:
        editor = os.environ['EDITOR']

    config_src = ''
    # If there is a pending update then use the configuration from
    # that in order to support incremental updates. Otherwise,
    # use the current EEPROM configuration.
    bootfs = shell_cmd(['rpi-eeprom-update', '-b']).rstrip()
    pending = os.path.join(bootfs, 'pieeprom.upd')
    if os.path.exists(pending):
        config_src = pending
        image = BootloaderImage(pending)
        current_config = image.get_file(BOOTCONF_TXT).decode('utf-8')
    else:
        current_config, config_src = read_current_config()

    create_tempdir()
    tmp_conf = os.path.join(TEMP_DIR, 'boot.conf')
    out = open(tmp_conf, 'w')
    out.write(current_config)
    out.close()
    cmd = "\'%s\' \'%s\'" % (editor, tmp_conf)
    result = os.system(cmd)
    if result != 0:
        exit_error("Aborting update because \'%s\' exited with code %d." % (cmd, result))

    new_config = open(tmp_conf, 'r').read()
    if len(new_config.splitlines()) < 2:
        exit_error("Aborting update because \'%s\' appears to be empty." % tmp_conf)
    apply_update(tmp_conf, eeprom, config_src)

def read_current_config():
    """
    Reads the configuration used by the current bootloader.
    """
    fw_base = "/sys/firmware/devicetree/base/"
    nvmem_base = "/sys/bus/nvmem/devices/"

    if os.path.exists(fw_base + "/aliases/blconfig"):
        with open(fw_base + "/aliases/blconfig", "rb") as f:
            nvmem_ofnode_path = fw_base + f.read().decode('utf-8')
            for d in os.listdir(nvmem_base):
                if os.path.realpath(nvmem_base + d + "/of_node") in os.path.normpath(nvmem_ofnode_path):
                    return (open(nvmem_base + d + "/nvmem", "rb").read().decode('utf-8'), "blconfig device")

    return (shell_cmd(['vcgencmd', 'bootloader_config']), "vcgencmd bootloader_config")

class ImageSection:
    def __init__(self, magic, offset, length, filename=''):
        self.magic = magic
        self.offset = offset
        self.length = length
        self.filename = filename
        debug("ImageSection %x offset %d length %d %s" % (magic, offset, length, filename))

class BootloaderImage(object):
    def __init__(self, filename, output=None):
        """
        Instantiates a Bootloader image writer with a source eeprom (filename)
        and optionally an output filename.
        """
        self._filename = filename
        self._sections = []
        self._image_size = 0
        try:
            self._bytes = bytearray(open(filename, 'rb').read())
        except IOError as err:
            exit_error("Failed to read \'%s\'\n%s\n" % (filename, str(err)))
        self._out = None
        if output is not None:
            self._out = open(output, 'wb')

        self._image_size = len(self._bytes)
        if self._image_size not in VALID_IMAGE_SIZES:
            exit_error("%s: Expected sizes %s bytes, got actual size %d bytes" %
                       (filename, VALID_IMAGE_SIZES, self._image_size))
        self.parse()
        self._is_ab_image = any(s.filename == "bootsys" for s in self._sections)

    def parse(self):
        """
        Builds a table of offsets to the different sections in the EEPROM.
        """
        offset = 0
        magic = 0
        while offset < self._image_size:
            magic, length = struct.unpack_from('>LL', self._bytes, offset)
            if magic == 0x0 or magic == 0xffffffff:
                break # EOF
            elif (magic & MAGIC_MASK) != MAGIC:
                raise Exception('EEPROM is corrupted %x %x %x' % (magic, magic & MAGIC_MASK, MAGIC))

            filename = ''
            if magic == FILE_MAGIC: # Found a file
                # Discard trailing null characters used to pad filename
                filename = self._bytes[offset + 8: offset + FILE_HDR_LEN].decode('utf-8').replace('\0', '')
            debug("section at %d length %d magic %08x %s" % (offset, length, magic, filename))
            self._sections.append(ImageSection(magic, offset, length, filename))

            offset += 8 + length # length + type
            offset = (offset + 7) & ~7

    def find_file(self, filename, partition_start=None, partition_end=None):
        """
        Returns the offset, length and whether this is the last section in the
        EEPROM for a modifiable file within the image.
        """
        offset = -1
        length = -1
        is_last = False

        if filename == BOOTCODE_BIN:
            next_offset = 0
            dst_filename = filename
            i = 0
            s = self._sections[i]
            offset = s.offset
            length = s.length
        else:
            next_offset = self._image_size - ERASE_ALIGN_SIZE # Don't create padding inside the bootloader scratch page
            if partition_end is not None:
                next_offset = min(next_offset, partition_end)
            for i in range(0, len(self._sections)):
                s = self._sections[i]
                if (partition_start is None or s.offset >= partition_start) and (partition_end is None or s.offset < partition_end):
                    if s.magic == FILE_MAGIC and s.filename == filename:
                        is_last = (i == len(self._sections) - 1)
                        offset = s.offset
                        length = s.length
                        break

        # Find the start of the next non padding section
        i += 1
        while i < len(self._sections):
            if self._sections[i].magic == PAD_MAGIC:
                i += 1
            else:
                next_offset = self._sections[i].offset
                break
        ret = (offset, length, is_last, next_offset)
        debug('%s offset %d length %d is-last %d next %d' % (filename, ret[0], ret[1], ret[2], ret[3]))
        return ret

    def update(self, src_bytes, dst_filename, bootcode = False):
        """
        Replaces a modifiable file with specified byte array.
        """
        if bootcode:
            hdr_offset, length, is_last, next_offset = self.find_file(dst_filename, partition_start=0, partition_end=READ_ONLY_SIZE)
            struct.pack_into('>L', self._bytes, hdr_offset + 4, len(src_bytes))
            struct.pack_into(("%ds" % len(src_bytes)), self._bytes, hdr_offset + 8, src_bytes)
            pad_start = hdr_offset + len(src_bytes) + 8
            is_last = False
            debug("bootcode padded to %d" % next_offset);
            if not self._is_ab_image and next_offset < 128 * 1024:
                raise Exception("update-bootcode: Can't update image - 128K must be reserved for bootcode")
            if next_offset < 0:
                raise Exception("update-bootcode: Failed to find next section")

        else:
            hdr_offset, length, is_last, next_offset = self.find_file(dst_filename, partition_start=READ_ONLY_SIZE, partition_end=READ_ONLY_SIZE + PARTITION_SIZE)
            update_len = len(src_bytes) + FILE_HDR_LEN

            if hdr_offset + update_len > self._image_size - ERASE_ALIGN_SIZE:
                raise Exception('No space available. %s size %d available space %d' % (dst_filename, update_len, self._image_size - ERASE_ALIGN_SIZE - hdr_offset))

            if hdr_offset < 0:
                raise Exception('Update target %s not found' % dst_filename)

            if hdr_offset + update_len > next_offset:
                raise Exception('Update %d bytes is larger than section size %d' % (update_len, next_offset - hdr_offset))

            new_len = len(src_bytes) + FILENAME_LEN + 4
            struct.pack_into('>L', self._bytes, hdr_offset + 4, new_len)
            struct.pack_into(("%ds" % len(src_bytes)), self._bytes,
                             hdr_offset + 4 + FILE_HDR_LEN, src_bytes)

            # If the new file is smaller than the old file then set any old
            # data which is now unused to all ones (erase value)
            pad_start = hdr_offset + 4 + FILE_HDR_LEN + len(src_bytes)

        # Add padding up to 8-byte boundary
        while pad_start % 8 != 0:
            struct.pack_into('B', self._bytes, pad_start, 0xff)
            pad_start += 1

        # Create a padding section unless the padding size is smaller than the
        # size of a section head. Padding is allowed in the last section but
        # by convention bootconf.txt is the last section and there's no need to
        # pad to the end of the sector. This also ensures that the loopback
        # config read/write tests produce identical binaries.
        pad_bytes = next_offset - pad_start
        if pad_bytes >= 8 and not is_last:
            pad_bytes -= 8
            struct.pack_into('>i', self._bytes, pad_start, PAD_MAGIC)
            pad_start += 4
            struct.pack_into('>i', self._bytes, pad_start, pad_bytes)
            pad_start += 4

        debug("pad %d" % pad_bytes)
        pad = 0
        while pad < pad_bytes:
            struct.pack_into('B', self._bytes, pad_start + pad, 0xff)
            pad = pad + 1

    def update_key(self, src_pem, dst_filename):
        """
        Replaces the specified public key entry with the public key values extracted
        from the source PEM file.
        """
        pubkey_bytes = pemtobin(src_pem)
        self.update(pubkey_bytes, dst_filename)

    def update_file(self, src_filename, dst_filename):
        """
        Replaces the contents of dst_filename in the EEPROM with the contents of src_file.
        """
        src_bytes = open(src_filename, 'rb').read()
        bootcode = dst_filename == BOOTCODE_BIN
        bootsys = dst_filename == BOOTSYS_BIN
        if not bootcode and not bootsys and len(src_bytes) > MAX_FILE_SIZE:
            raise Exception("src file %s is too large (%d bytes). The maximum size is %d bytes."
                            % (src_filename, len(src_bytes), MAX_FILE_SIZE))
        self.update(src_bytes, dst_filename, bootcode)

    def set_timestamp(self, timestamp):
        """
        Sets the self-update timestamp in an EEPROM image file. This is useful when
        using flashrom to write to SPI flash instead of using the bootloader self-update mode.
        """
        ts = int(timestamp)
        hdr_offset, _, _, _ = self.find_file(UPDATE_TIME_FILENAME, partition_start=0, partition_end=READ_ONLY_SIZE)
        if hdr_offset < 0:
            # No timestamp file found, so use the last 4 bytes of the image
            struct.pack_into('<L', self._bytes, len(self._bytes) - 4, ts)
            struct.pack_into('<L', self._bytes, len(self._bytes) - 8, ~ts & 0xffffffff)
            return
        
        # Set the update timestamp in the read only section
        contents_offset = hdr_offset + 4 + FILE_HDR_LEN
        struct.pack_into('<L', self._bytes, contents_offset + 4, ts)
        struct.pack_into('<L', self._bytes, contents_offset, ~ts & 0xffffffff)
        
        # Set the update timestamp in the partition
        hdr_offset, _, _, _ = self.find_file(UPDATE_TIME_FILENAME, partition_start=READ_ONLY_SIZE, partition_end=READ_ONLY_SIZE + PARTITION_SIZE)
        if hdr_offset < 0:
            raise Exception("Failed to find update time file in partition")
        contents_offset = hdr_offset + 4 + FILE_HDR_LEN
        struct.pack_into('<L', self._bytes, contents_offset + 4, ts)
        struct.pack_into('<L', self._bytes, contents_offset, ~ts & 0xffffffff)
            

    def write(self):
        """
        Writes the updated EEPROM image to stdout or the specified output file.
        """
        if self._out is not None:
            self._out.write(self._bytes)
            self._out.close()
        else:
            if hasattr(sys.stdout, 'buffer'):
                sys.stdout.buffer.write(self._bytes)
            else:
                sys.stdout.write(self._bytes)

    def get_file(self, filename):
        hdr_offset, length, is_last, next_offset = self.find_file(filename)
        if filename == BOOTCODE_BIN:
            offset = hdr_offset + 8
            file_bytes = self._bytes[offset:offset+length]
        else:
            offset = hdr_offset + 4 + FILE_HDR_LEN
            file_bytes = self._bytes[offset:offset+length-FILENAME_LEN-4]

        return file_bytes

    def extract_files(self):
        for i in range(0, len(self._sections)):
            s = self._sections[i]
            if s.magic == MAGIC and s.offset == 0:
                file_bytes = self.get_file(BOOTCODE_BIN)
                open(BOOTCODE_BIN, 'wb').write(file_bytes)
            elif s.magic == FILE_MAGIC:
                file_bytes = self.get_file(s.filename)
                open(s.filename, 'wb').write(file_bytes)

    def read(self):
        config_bytes = self.get_file('bootconf.txt')
        if self._out is not None:
            self._out.write(config_bytes)
            self._out.close()
        else:
            if hasattr(sys.stdout, 'buffer'):
                sys.stdout.buffer.write(config_bytes)
            else:
                sys.stdout.write(config_bytes)

def main():
    global DEBUG
    """
    Utility for reading and writing the configuration file in the
    Raspberry Pi bootloader EEPROM image.
    """
    description = """\
Bootloader EEPROM configuration tool for the Raspberry Pi 4 and Raspberry Pi 5.
Operating modes:

1. Outputs the current bootloader configuration to STDOUT if no arguments are
   specified OR the given output file if --out is specified.

   rpi-eeprom-config [--out boot.conf]

2. Extracts the configuration file from the given 'eeprom' file and outputs
   the result to STDOUT or the output file if --output is specified.

   rpi-eeprom-config pieeprom.bin [--out boot.conf]

3. Writes a new EEPROM image replacing the configuration file with the contents
   of the file specified by --config.

   rpi-eeprom-config --config boot.conf --out newimage.bin pieeprom.bin

   The new image file can be installed via rpi-eeprom-update
   sudo rpi-eeprom-update -d -f newimage.bin

4. Applies a given config file to an EEPROM image and invokes rpi-eeprom-update
   to schedule an update of the bootloader when the system is rebooted.

   Since this command launches rpi-eeprom-update to schedule the EEPROM update
   it must be run as root.

   sudo rpi-eeprom-config --apply boot.conf [pieeprom.bin]

   If the 'eeprom' argument is not specified then the latest available image
   is selected by calling 'rpi-eeprom-update -l'.

5. The '--edit' parameter behaves the same as '--apply' except that instead of
   applying a predefined configuration file a text editor is launched with the
   contents of the current EEPROM configuration.

   Since this command launches rpi-eeprom-update to schedule the EEPROM update
   it must be run as root.

   The configuration file will be taken from:
       * The blconfig reserved memory nvmem device
       * The cached bootloader configuration 'vcgencmd bootloader_config'
       * The current pending update - typically /boot/firmware/pieeprom.upd

   sudo -E rpi-eeprom-config --edit [pieeprom.bin]

   To cancel the pending update run 'sudo rpi-eeprom-update -r'

   The default text editor is nano and may be overridden by setting the 'EDITOR'
   environment variable and passing '-E' to 'sudo' to preserve the environment.

6. Signing the bootloader config file.
   Updates an EEPROM binary with a signed config file (created by rpi-eeprom-digest) plus
   the corresponding RSA public key.

   Requires Python Cryptodomex libraries and OpenSSL. To install on Raspberry Pi OS run:-
   sudo apt install python3-pycryptodome

   rpi-eeprom-digest -k private.pem -i bootconf.txt -o bootconf.sig
   rpi-eeprom-config --config bootconf.txt --digest bootconf.sig --pubkey public.pem --out pieeprom-signed.bin pieeprom.bin

   Currently, the signing process is a separate step so can't be used with the --edit or --apply modes.


See 'rpi-eeprom-update -h' for more information about the available EEPROM images.
"""
    parser = argparse.ArgumentParser(formatter_class=argparse.RawDescriptionHelpFormatter,
                                     description=description)

    parser.add_argument('-a', '--apply', required=False,
                        help='Updates the bootloader to the given config plus latest available EEPROM release.')
    parser.add_argument('-c', '--config', help='Name of bootloader configuration file', required=False)
    parser.add_argument('-e', '--edit', action='store_true', default=False, help='Edit the current EEPROM config')
    parser.add_argument('-o', '--out', help='Name of output file', required=False)
    parser.add_argument('-d', '--digest', help='Signed boot only. The name of the .sig file generated by rpi-eeprom-digest for config.txt ', required=False)
    parser.add_argument('-p', '--pubkey', help='Signed boot only. The name of the RSA public key file to store in the EEPROM', required=False)
    parser.add_argument('-x', '--extract', action='store_true', default=False, help='Extract the modifiable files (boot.conf, pubkey, signature)', required=False)
    parser.add_argument('-b', '--bootcode', help='Signed boot 2712 only. The name of the customer signed bootcode.bin file to store in the EEPROM', required=False)
    parser.add_argument('-s', '--bootsys', help='Signed boot 2712 only. The name of the customer signed bootsys.bin file to store in the EEPROM', required=False)
    parser.add_argument('-t', '--timestamp', help='Set the timestamp in the EEPROM image file', required=False)
    parser.add_argument('--cacertder', help='The name of a CA Certificate DER encoded file to store in the EEPROM', required=False)
    parser.add_argument('--debug', help='Debug logging for this tool', action='store_true', required=False)
    parser.add_argument('eeprom', nargs='?', help='Name of EEPROM file to use as input')
    args = parser.parse_args()
    DEBUG = args.debug

    if (args.edit or args.apply is not None) and os.getuid() != 0:
        exit_error("--edit/--apply must be run as root")

    if (args.edit or args.apply is not None) and not rpi4() and not rpi5():
        exit_error("--edit/--apply must run on a Raspberry Pi 4 or Raspberry Pi 5")

    if args.edit:
        edit_config(args.eeprom)
    elif args.eeprom is not None and args.extract:
        image = BootloaderImage(args.eeprom, args.out)
        image.extract_files()
    elif args.apply is not None:
        if not os.path.exists(args.apply):
            exit_error("config file '%s' not found" % args.apply)
        apply_update(args.apply, args.eeprom, args.apply)
    elif args.eeprom is not None:
        image = BootloaderImage(args.eeprom, args.out)
        if args.timestamp is not None:
            image.set_timestamp(args.timestamp)

        if args.bootcode is not None:
            image.update_file(args.bootcode, BOOTCODE_BIN)
        
        if args.bootsys is not None:
            image.update_file(args.bootsys, BOOTSYS_BIN)

        if args.cacertder is not None:
            image.update_file(args.cacertder, CACERT_DER)

        if args.config is not None:
            # The public key, EEPROM config and signature should be set together
            if not os.path.exists(args.config):
                exit_error("config file '%s' not found" % args.config)
            image.update_file(args.config, BOOTCONF_TXT)
            if args.digest is not None:
                image.update_file(args.digest, BOOTCONF_SIG)
            if args.pubkey is not None:
                image.update_key(args.pubkey, PUBKEY_BIN)

        if args.config is not None or args.timestamp is not None or args.bootcode is not None or args.cacertder is not None:
            debug("Writing image")
            image.write()
        else:
            image.read()
    elif args.config is None and args.eeprom is None:
        current_config, config_src = read_current_config()
        if args.out is not None:
            open(args.out, 'w').write(current_config)
        else:
            sys.stdout.write(current_config)

if __name__ == '__main__':
    atexit.register(exit_handler)
    main()